Products

Table Saws - Miter Saws - Undercut Saws - Notching Machines

KNA AIR OPERATED UNDERCUT SAWS

Tech. Data	Model 800	Model 1200	Model 1600
Working Height	36" (914 mm)	36" (914 mm)	36" (914 mm)
Cut off Capacity	2" x 8"	2" x 12"	2" x 16"
Motor Standard TEFC	5 HP/3/60 HZ	7 ½ HP/3/60 HZ	10 HP/3/60 HZ
Starter	Magnetic Type
Arbor	1" for Blade
Panel Mounted Speed	OPTIONAL	STANDARD	STANDARD
Adjustable Speed:	up to 120 cycles/min	up to 100 cycles/min	up to 60 cycles/min
Saw blade Capacity	14" dia.	18" dia.	20" dia.

PISTORIUS MODELS UC 16, 18 Under Cut-Off Saws

These saws are designed to fill basic cross-cutting requirements for rough sizing and defecting applications. Ideal for large or small plants, the machine is designed with simplicity in mind, for a minimum investment and minimal maintenance. Ideal for use in many applications such as furniture, louver door, cabinets, pallets, clocks, finger joint systems, novelties, wood product manufacturers, sash and door plants, dimension plants and many other applications.

Features:

High-speed Pneumatic and Hydropneumatic models.
Protective see-through guard on both sides of cutting area.
Simple compressed air operation.
Wide range of gage systems available.
Left & right hand feed available.
Floating blade guard.
Automatic full-length clamping.

PISTORIUS MITER SAW MODELS EMN-12 and EMN-14

Foot or Air operated double miter cut-off saws. Extremely versatile. Sawblades will cut nearly any material in one cycle of the sawheads, not repeated chopper-like passes. Each cut is a finish cut suitable for assembly. No material supports are necessary as no pressure is exerted against the work piece. This machine will easily cut through any flat shape, and with no fixturing, will handle small reverses and shell-type mouldings..

Features:

230 volt, 1 phase electrics standard. No expensive electrical installation required.
Simple and effortless to use. Employee’s become very efficient and accomplished at operating this machine.
Side scrap-discharge chute keeps scrap away from operator. Simple disposal into container.
Machine is virtually maintenance free, eliminating costly downtime. Keeping blades sharp is your only requirement for continuous trouble free operation.
Complete line of gages and quality carbide sawblades available.
Manual model does not require compressed air.

PISTORIUS MODELS MN-201, 202, 301 Staggered Head Double Miter Pivot Saw

Staggered saw models can be used for either conventional double mitering or “notching” when using the appropriate fixtures and gages as illustrated and described in bulletin MN. This unique design feature allows the machine to be utilized for two different applications, expanding its usefulness and providing a quicker payback.

Typical Uses:

Kitchen cabinet toe-kick cut outs.
Combination cabinet door mitering and toe-kick cut outs.
Aluminum wrap around luggage and case frames.
Aluminum wraparound display, directory and appliance or vending machine frames.

CTD 200 SERIES 10" & 12" Fixed, Miter & Compound Miter Cut-Off Saws

Blade Capacity: 10", 12", 14"
Spindle & Pivot Shaft: have pre-loaded, sealed ball bearing; .001 alignment of spindle and pivot
Motors: 2 - 5 HP
Blade Guard.
Extras: Power Feeds, Clamps, Magnetic starters, Measuring Fences and Tables.

CTD Model F426, 16” & Model F526, 20” Straight 90° Cutting Saws & 400 SERIES

Blade Capacity: Models M416 & F426, 16” OD (406mm); Models M516 & F526, 20” OD (504mm)
Arbor: 1” (25mm) with 5” (127mm) saw collars.
Spindle mounted on preloaded
and sealed bearings; with V-belt drive completely
enclosed; pivot uses Timken bearings lubricated for life.
7-1/2 H.P. 3 Phase 230/460 Volt Totally Enclosed Fan Cooled Motor with Magnetic
Starter standard; 10 H.P. & 15 H.P. motors available
as optional extra.
Floor Stand: Heavy gage steel sheet and angle.
Two 4” (102mm) outlets provided;

Size & Weight: 48” (122cm) Wide x 40” (102cm) Front to Back x 70” (178cm) High; Weight is 850 lbs. (386kg).

Optional Extras Include: Power Downfeeds of Sawheads, Clamps, Measuring Systems and
Table Supports.

CTD MODEL N80&N90 1" Vertical Frame & Notching Saw

Blade Capacity: 13/16/18"
Arbor: 1" Mounted on pre-loaded and sealed bearings; 2-belt drive
Motors: Two 2 HP 3 Phase. 5 HP Motors available
Table Base: Precision machines and ground iron castings with milled key-ways to guide fences.
Floor Stand: Heavy gage steel, completely encloses with 6" dust collector outlet and scrap chute
Actuation: Air operated by foot valve with cover

CTD Model CM60 16” Mitre & Compound Mitre Saw

Optional Extras Include: Power Downfeeds of Sawheads, Clamps, Measuring Fences and Table Supports. Cutting Capacity: 45° Mitre; 4” (102mm) High x 7-1/4” (184mm) Wide 90° Straight Cut; 4” (102mm) High x 10-1/2” (267mm) Wide 90° Front to Back/45° Compound; 2-5/8” (67mm) High x 10” (254mm) Wide.

- Blade Capacity: 16” (406mm)
- Arbor: 1” (25mm) with 3-1/2” (89mm) saw collars;
mounted on preloaded and sealed bearings; 2-belt
drive centered between bearings; 2800 RPM of spindle.
- Motors & Voltages: 3 H.P. 3 Phase 230/460 Volt Totally
Enclosed Fan Cooled Motor, 60 Hz, 1725 RPM with starter;
5 H.P. available. Consult factory for amperage ratings.
- Actuation: Hand operated standard; optional power
downfeeds of sawheads actuated by Two-Hand, Anti-Tie Down Maintained Contact Safety Control.

CTD "Miter Max" DMC70
13" 45° Double Mitre Cross-cut Saw

- Blade Capacity: 13” OD (330mm)
- Arbor: 1” (25.4mm) with 3” (76mm) saw collars; mounted on preloaded and sealed bearings; 2 groove belt drive:
3450 RPM of spindle.
- Motors & Voltages: 1 1/2 H.P. single phase, 230 Volt,
- Totally Enclosed Fan Cooled Motors; 60 Hz, 3450 RPM with Dual Magnetic Starter.
-Floor Stand: Heavy gage steel; stand is completely enclosed with two 4" (101mm) dust collector outlets and removable dust and scrap drawer.
- Includes 60" (152cm) long lined vision gauge for measuring inside mitres; a 72" (189cm) long outside fence with tape, pointer and stop; and infeed and outfeed material support tables 10" (25cm) Wide x 48" (122cm) Long.

Actuation: "H" model is manually hand operated. “A” model is pneumatically operated with options to operate left blade, right blade or both blades. “A” model includes two pneumatic horizontal clamps and FRL unit with auto drain.
- Air Consumption: 3 CFM at 80 PSI (.09 cubic meters/minute at 5.6 kg/cm2) based on 10 strokes per minute; includes air filter/regulator/lubricator with auto drain.
- Size & Weight: 57” (145cm) Wide x 33” (84cm) front to back x 45” (114cm) High Over all Length with tables and measuring system 153” (387cm) Weight 650 lbs (294 kg)
- Production Rate: Up to 10 strokes per minute.
- Cutting Capacity: 8” (203mm) Wide x 4” (101mm) High

- Length of Stroke Adjustment: The D45FX is unique in that the stroke of the machine and the position of
the blade above the work can be adjusted to use only the stroke needed to cut a particular molding or extrusion.
- Adjustment bolts in slots position saws close to work,
thereby saving time and motion.
- Floor Stand: Close coupled heavy gage steel stand
completely enclosed with 6” dust outlet. 1200 CFM
required.
- Actuation: Manual foot pedal.

CTD Model D45FX&AX Frame & Notching Saw

The D45FX Foot Operated Double Mitre Saw incorporates
all the features and specifications of the D45AX except that it is manually foot operated.

- Blade Wear and Angular Adjustments: Each saw head
has adjustments for blade variation. Allows for precision
alignment of blades to minimizes scrap. Saw heads are
adjustable up to 3°, always assuring perfect mitres.

DELTA Unisaw 10"Tilting Arbor Saw - Left or Right Tilt

5 HP 200-230/460V, 60 Hz., 3450 rpm three phase motor with push-button station, magnetic starter. Includes TEFC motor enclosure, equipment mounting hooks, see-through blade guard, 10" diameter combination blade, miter gage, table insert, motor pulley, 3/4 bore, set of three matching V-belts, dust port for 4" dust collection hose and instruction manual.

Three-phase electricals will be supplied wired for 230V unless 460V is specified. 24V with transformer and 3-leg overload protection (LVC).

Single phase, 3 HP electricals will be supplied wired for 230V only. Power cord and Plug supplied on 3 HP, single phase UNISAWS only. Motor and Motor controls for Delta 10" UNISAWS may be ordered mounted.

DELTA Model 36-R31

Delta Industrial Model 36-R31 with a 3 HP 230V, 60 Hz., 3450 rpm single phase motor with full-voltage motor starter (GPE). Includes TEFC motor enclosure, equipment mounting hooks, see-through blade-guard, 10" diameter combination blade, miter gage, table insert, motor pulley, 3/4 bore, set of 3 matching V-belts, 4" dust collection port, and instruction manual.

DELTA Cabinet 10" Tilting Arbor Saw

Motor - TEFC: 2 HP
Arbor: 5/8
Blade: 10"

43" x 59" table with two extension wings and fence support extension.

DELTA Model 36-790

Delta Industrial Model 36-790 14"/16" Tilting Arbor Saw includes a 7 1/2 HP, 200-220/440V (wired for 200-220V), 60 Hz., 3 phase motor with magnetic starter and automatic reset overload; blade guard splitter, Biesemeyer® Commercial Fence System, guide bar, miter gage.